6 29 2015 TLR 2 qPCR

Yesterday I ran a replicate of the TLR2.1 qPCR for statistical purposes. Hopefully this will help determine some interesting differences between samples.

Primers:

1630	TLR2.1_FWD	ACAAAGATTCCACCCGGCAA	JH	5/21/2015	20	55		O.lurida	Toll-like receptor 2 type-1	Q9DD78
1629	TLR2.1_REV	ACACCAACGACAGGAAGTGG	JH	5/21/2015	20	55		O.lurida	Toll-like receptor 2 type-1	Q9DD78

Reagent Table:

	Volume	Reactions X58
Ssofast Evagreen MM	10	580
FWD Primer	0.5	29
REV Primer	0.5	29
Nuclease Free H2O	8	464
cDNA	1

1. Added reagents from greatest to least volume
2. Vortexed
3. Centrifuged briefly
4. Pipetted 19 ul Master Mix to each tube
5. Pipetted appropriate cDNA sample to each tube
6. Centrifuged plate at 2000 rpm for 1 minute
7. Ran Program Below

Program:

Step	Temperature	Time
Initiation	95 C	10 min
Elongation	95 C	30 sec
	60 C	1 min
Read
	72 C	30 sec
Read
Repeat Elongation 39 times
Termination	95 C	1 min
	55 C	1 sec
Melt Curve Manual ramp 0.2C per sec Read 0.5 C	55 - 95 C	30 sec
	21 C	10 min
End

Plate Layout:

1	2	3	4	5	6	7
DNased 42215 HC1	DNased 42215 NC1	DNased 42215 SC1	DNased 42215 HT1 1	DNased 42215 NT1 1	DNased 42215 ST1 1	NTC
DNased 42215 HC2	DNased 42215 NC2	DNased 42215 SC2	DNased 42215 HT1 2	DNased 42215 NT1 2	DNased 42215 ST1 2	NTC
DNased 42215 HC3	DNased 42215 NC3	DNased 42215 SC3	DNased 42215 HT1 3	DNased 42215 NT1 3	DNased 42215 ST1 3	NTC
DNased 42215 HC4	DNased 42215 NC4	DNased 42215 SC4	DNased 42215 HT1 4	DNased 42215 NT1 4	DNased 42215 ST1 4	NTC
DNased 42215 HC5	DNased 42215 NC5	DNased 42215 SC5	DNased 42215 HT1 5	DNased 42215 NT1 5	DNased 42215 ST1 5
DNased 42215 HC6	DNased 42215 NC6	DNased 42215 SC6	DNased 42215 HT1 6	DNased 42215 NT1 6	DNased 42215 ST1 6
DNased 42215 HC7	DNased 42215 NC7	DNased 42215 SC7	DNased 42215 HT1 7	DNased 42215 NT1 7	DNased 42215 ST1 7
DNased 42215 HC8	DNased 42215 NC8	DNased 42215 SC8	DNased 42215 HT1 8	DNased 42215 NT1 8	DNased 42215 ST1 8

Results:

All Samples

NTCs

It appears there was some contamination in 1 of the 4 NTCs but it doesn't appear in any of the others. After running this I will need to run a replicate using CRAF and do analysis on all of the data sets produced. 

You can view the raw data here.